Tons of Used Parts …Chapter V
Posted by Michael on 10 Dec 2007 at 10:55 am | Tagged as: Healey Stuff
I’m not trying to make things difficult but I have found that describing corroded or damaged body panels is impossible therefore I have decided to sell the few that I have left in stock in restored condition only.
The restoration work has, or will be, done by a former employee who used to do all our metal restoration work using masses of patterns and bucks which he has accumulated over the years.
Such panels will be supplied in ready to install condition with hammered butt welds and no paint or filler.
Mounting holes in the replaced areas may have to be drilled, as variations can occur from car to car, and minor “spot putty” will be required during the refinishing process.
The insides are not usually completely stripped or cleaned because, if you require this, it is more cost effective for you to use your time rather than pay a skilled panel beater to do it.
I have a VERY limited number of most of these panels and when they are gone they are gone.
The prices for the restored panels are as follows
FENDERS
6 Cyl convertible front $900 (SOLD)
6 Cyl roadster front $900 (1pr & 2 left available)
4 Cyl front $850 (1 pr available)
BN2 & 6 Cyl rear $600 (3 pr & 7 left available) 1 pr completed
BN1 rear $650 (1 pr available) 1 completed
I have one new reproduction 6 cylinder right rear fender which, typically, does not fit. Anyone can have it for $100 + shipping, but believe me you would be better starting off with one from a ‘53 Buick Special.
SHROUDS
4 Cyl front $2300 (6 available)
6 Cyl roadster front $2300 (7 available)
6 Cyl conv front (single light) $2700 (SOLD)
6 Cyl conv front double light $2900 (1 available) Sold
4 Cyl rear $2600 (4 available)
6 Cyl 2 seater rear $2800 (2 available)
6 Cyl 4 seater roadster rear $2300 (11 available)
6 Cyl conv (early) rear $2900 (SOLD)
6 Cyl conv (late) rear $2900 Completed
For panels which are not in finished stock I will require a 50% deposit with each order.
Depending upon the amount of work we have ahead of us production of a finished panel can take up to 4 weeks.
As mentioned earlier if these panels have to be shipped there will be a crating charge which is typically $50 for fenders and $120 for shrouds.
You can download the full list here:
scott-morris-list-modified.xls
Hi Michael.
Need rhs steering arm for a BN6. Mine is bent and I presume not repairable.
I’m not in a hurry so you need not make a special trip.
Let me know price. Thanks
Michael,
I like your website. You obviously have an indepth knowledge about Healeys and I thought you just might information or the particular part I am trying to locate. It is a ‘lockring’(part # 17H6536 as listed in the late Healey 3000 Mechanical Parts Steering Section) as was used on the Austin Healey and possibly other BMC C series steering columns back in the 60s and possibly
the 70s. It is a splined collar, several inches long, with a pince bolt that fits the splines on the adjustable steering column and has a slot into which the steering column/ignition lock pin fits when the vehicle is parked and the ignition key is removed. It then locks the steering column. I am quite sure this will only be found on an old column of which VERY few
locking mechanisms were installed. Any reply will be
greatly appreciated and Thanks for your time in checking on this.
Best Regards,
don
Best Regards, d
ichael,
Dear Michael,
I am looking for a complete roll-up window assembly for a late model BJ8 (window, channels, vent window, winder mechanism). Please let me know if you can supply these parts and and an approximate cost. Thanks much, John