During the final weeks of the restoration of my early Austin Healey 100 it became apparent that acquisition of original style batteries was going to become a major problem.
The only “acceptable” batteries for a concours car are original “Lucas” 6 volt 17L “tar-top” batteries.
I had acquired a pair of originals with a view to having them rebuilt but, when I made inquiries about having this done, it quickly became obvious that this was just not going to happen as the only re-builders that I could find worked exclusively on large industrial batteries and had neither the parts nor any interest in tackling such a small job.
I had had a pair of reproductions on order for some months but calls to the supplier were not encouraging and the chances of getting them before Enclave 2015 were virtually nil!
I decided that an alternate plan was called for.
I had seen several track racing minis equipped with Ballistic Lithium Ferrous Phosphate batteries and, having had some experience with starting highly tuned competition engines, I felt sure that if one of these batteries could start a race mini it could probably start a Healey 100 engine with a compression ratio of only 7.5:1. When one of the mini racers mentioned that his Ballistic battery had provided good service for 3 seasons I was convinced.
The problem is of course that this modern battery really did not look much like the old “tar-top” Lucas relic from 1953!!
However, upon further investigation, it became apparent that the tiny size of these modern batteries meant that one with sufficient cranking capacity for a Healey would easily fit inside the case of the original Lucas battery.
Here is how it is done.
Of course to start you have to have a pair of original or reproduction tar-top batteries to modify.
CAUTION : BATTERY ACID IS VERY CORROSIVE. WEAR GOGGLES AND GLOVES
Be sure to use rubber gloves and wear goggles while working with the battery.
First confirm that the battery is TOTALLY discharged by checking that the voltage cross the terminals is ZERO.
Next remove the fill caps and drain all the old electrolyte (acid) out of the original batteries. Refill the battery with water and drain 2 or 3 times to neutralize the electrolyte. Also see if you can safely recycle the acid and do not run it down the drain. Do rinse the case over and over before you start cutting and pulling stuff out. You may also want to wear a mask as acid fumes are nasty. (Thanks Ira).
The next task is a bit brutal.
Using a sharp handsaw saw or similar implement of destruction cut the tops off the original batteries. Cut straight across all the way just below the bottom of the hold down lugs then pull out all the lead plates and dispose of them safely.
The next task is to remove the 2 dividing partitions from the case of one of your 2 batteries. These need to be cut out right down until they are level with the grid in the bottom of the case. A multi-purpose oscillating tool works quite well for this but I’m sure there are plenty of other methods. Once you are done the cavity within the case will be around 6 3/8″ long x 5 5/8″ wide x 4 3/4″ high.
Note: With the second battery it is only necessary to cut some small “V”s out of the top of the partitions but we didn’t figure that out until all the work had been done to remove them entirely.
To ensure that the lid will index accurately when replaced on the case we installed some plastic guides on the underside of the lid.
Once this is done you will find that your new Ballistic EVO2 16 Cell battery will easily fit right inside the case.
I used some strips of Styrofoam insulation to “nest” the Ballistic battery and ensure that it wouldn’t rattle around inside the case.
The next task is to connect the Ballistic battery to the +ve and –ve posts molded into the lid of your original battery. These connections and the cables will have to carry the full load of the starter so they have to be fairly substantial.
I used sections of some old heavy duty booster cables to make up short jumpers for this. It was necessary to drill and tap the undersides of the posts to secure the terminals that I had soldered onto the ends of my jumpers. Be sure to make the jumpers long enough that you can attach the Ballistic battery terminals to them as you install the lid.
With the second battery it is only necessary to make up a jumper, again heavy duty, to link the +ve and -ve terminals. That is why some small “V”s in the partitions on the second battery are all that is required.
It is not necessary to glue the top back in position as the as the original battery securing rods will hold it in place..
Now install the batteries into the car and you are almost finished.
One last thing and this is very important if you want your expensive lithium ferrous phosphate batteries to last a long long time.
The instructions that come with the Ballistic battery emphasize that over charging will permanently damage the battery so it is essential that you adjust the regulated output of your generator to ensure that the maximum voltage that it can produce is 13.6 volts.
I found this very simple to achieve and procedure is clearly explained in section O/13 of the Factory Workshop Manual. It is the regulator adjustment that needs to be adjusted as this is normally set to something around 15.5 volts for a lead/acid battery.
Use a digital voltmeter to get it right and make sure that you drive the car while checking the revised output voltage just to ensure that it is correct.
I would recommend leaving a note inside the cover of the regulator indicating that it will require readjustment if lead acid batteries are installed in the car at some later time because an output setting of 13.6 volts will decrease the storage capacity of such batteries.
A couple of other things that are important to remember are:
- Just like a lead acid battery your Ballistic battery will be permanently damaged if allowed to completely discharge so be sure to turn off your master switch when you are storing the car for more than a few days.
- A regular battery charger is capable of delivering more than 13.6 volts… Be sure to use one that will not overcharge your Ballistic battery
I’m constantly on the lookout for other models of lithium batteries that my be suitable for this modification and one has come to light.
These 6 volt batteries are small enough that 2 could easily be accommodated within a 17L battery case and, as they are 6 volt, they could be arranged in a parallel and series combination in both battery cases to provide superior service.
The layout would be like this:
This would provide considerably more capacity than the single Ballistic battery but there is a bit of a downside … The AG-1202 batteries are $229.99 EACH!!!