AN INTERESTING THING ABOUT CLUTCHES

One of the cars that I own is a 1992 Mitsubishi 3000 GT VR4.

photo rearI purchased this car many years back and use it quite a bit in the summer months. It is absolutely stock and a real pleasure to drive however, a couple of years back, the clutch started to give some trouble.

If you know all about clutches you can skip the next bit because it is just a primer for those not familiar with how they work.

Modern clutches, that is clutches designed after the mid sixties, are called “diaphragm “clutches.

Exploded clutch small

This type of clutch replaced the “spring” clutches in use at the time because they were less complex, lighter, stronger and cheaper to make.

There are various styles of diaphragm clutch but they all operate in the same way and are based upon the principle of a diaphragm spring (know also as a Belleville spring and named after its inventor Julian F Belleville) and use the pressure exerted by the diaphragm spring to clamp the clutch disc between the pressure plate and the flywheel.

Clutch operation smallBecause they are friction devices all clutches are subject to wear and, when they wear, they fail to transmit the torque to which they are subjected and start to slip.  Because the diaphragm spring, which provides the clamping force in the clutch has a very limited range of movement these clutches tend to slip when they get worn.

Because the VR4 is all wheel drive and produces over 300 BHP the clutch is a pretty substantial unit that it uses a vacuum assist unit to decrease the required pedal pressure.

The problem I encountered was that the clutch pedal was getting harder and harder to depress but the clutch was starting to slip under high loads. My initial suspicion was that the servo assist unit was starting to fail but, when I expelled the entire vacuum and tried to operate the clutch without its assistance I could hardly press the pedal to the floor with one foot. When I tried this with the clutch in a friend’s Stealth Twin Turbo, essentially the same car, the pedal was noticeably heavier without the servo assistance but could still be operated, with difficulty, with one leg.

These symptoms just did not add up. All my experience prior to this had been with British cars. In those cars clutch slip was always associated with a decrease of required pedal pressure because as the clutch slipped it overheated and weakened the diaphragm spring.  In fact I’ve seen MGB clutches which have been overheated to such an extent that the diaphragm spring had become a flat limp piece of blue steel which had absolutely no resilience at all!!

The symptoms exhibited by the VR4 clutch bore no resemblance at all to what I was used to.  Finally, despite my policy of diagnosing a problem before trying to fix it, the clutch became unbearably heavy so I decided that I had no option but to replace it to see if the problem went away.

I changed the clutch, not my favorite job on any car and particularly difficult in the AWD VR4 and voila, everything was perfect…

So…what was wrong with the clutch I removed? It appeared to be the original and although the friction disc was well worn it was still in very good condition with no sign of having been overheated.

After a bit of study I did finally figure out what was wrong…

Can you explain the cause of the symptoms that I was experiencing?

About Michael

Who is this guy? Born in New Zealand some time back. Went to Maori Hill Primary School then Kaikorai Valley High before joining the RNZAF and an Airman Cadet in 1968. Graduated 1972 with an NZCE in Aeronautical Engineering. Then embarked on the typical Kiwis "Big Trip Overseas". Got to see quite a few places, and spent a while in the U.K. "home" as it was refered to by many New Zealanders in those days, before travelling on to New York and then to Canada by bus!! This trip is presently on hold (has been for the last 34 years). Met my dear wife Judy not long after arriving in Ontario and we have been happily married since 1976. After travelling around New Zealand and the pacific in 1979 I started Precision Sportscar andfor the next 23 years grew the business and helped raise 2 boys Drew and Robin.
This entry was posted in Mitsubishi 3000 GT VR4. Bookmark the permalink.

5 Responses to AN INTERESTING THING ABOUT CLUTCHES

  1. Charlie Baldwin says:

    I’d guess that work hardening had something to do with it.

  2. Michael says:

    Well yes.. it was hard work to push the clutch down when it had the problem but …. ahhh ummm that wasn’t the cause of the problem.

  3. Michael salter says:

    The problem was that as a result of the wear on the friction disc the diaphragm spring had over extended.
    This meant that the release bearing was pressing on diaphragm at an ineffective angle.
    Installing a new disc with the original spring (as a test) resulted in the fingers of the spring being about 2 cm lower.
    Just changing the friction disc probably would have solved the heavy clutch issue but most likely the slip issue would have remained.
    I’m not sure if the clutch I removed was an original or an aftermarket but the geometry was definitely way out once the disc thickness got down.

  4. sajin mohammed says:

    wow it naice

  5. Warren Voth says:

    Thanks for your help Michael,

    This problem only started with the hydraulic master and slave cylinders and flex line replacement. The clutch has never slipped since it’s replacement in 1999. At this point, I am at a loss as to the problem. Input from the INTERNET everywhere tells me this is not a common problem, and maybe unique to my car. I will be in contact with Apple Hydraulics to see if they have heard of anything like this on clutch master cylinder re-builds. I may end up pulling the transmission as a last resort.

    Thanks again, Warren

Leave a Reply

Your email address will not be published. Required fields are marked *